Our documentation has been relocated here, the Liferay Developer Network. Please update your bookmarks!

There are multiple ways to skin the search cat (disclaimer: no actual cats have been harmed during the writing of this article).

If you’re unsure which approach to take, use the default configuration. It provides a sensible starting point that can be modified later, as needed.

If you’ve been using Liferay Portal for a long time and like the search experience you’ve always used, use the legacy approach.

If you’re in need of a fully customized experience, manually configure the search experience.

After choosing your approach and reading here to get it up and running, find the articles on the Search Bar, Search Facets, and Search Results to understand the full suite of configuration options.

Search display pages are where users go to enter search terms and browse search results.

Default Search Pages

Using the default site and the default theme with the default search settings, the out-of-the-box search experience has two components for end users:

  1. A search bar embedded on each page.
  2. A default search page where search requests are routed.

Behind the scenes, The search bar widget points to a hidden search page with the friendly URL /search.

search-dest-page.png

Figure 1: By default, the embedded search bar points to the pre-configured /search destination page.

Enter a search term and you’re redirected to the default search page, where results are displayed in the Search Results widget.

search-default-page.png

Figure 2: The default page is pre-configured with the Search Results widget and the various Facet widgets to provide a full search experience.

The default search page is based on a Search page template, but it doesn’t inherit changes from the page template by default. That means you can customize the search page directly without changing the template’s inheritance configuration.

search-page-config.png

Figure 3: Configure the Search page. By default, it doesn’t inherit changes from the page template.

If you require just a few changes to the default page, don’t abandon it and create one manually. Just make the configuration changes you need, including adding, configuring, and removing widgets on the page. On the other hand, if you want a clean break from the default search page, starting from scratch is also an option.

Manual Search Page Configuration

It’s reasonable to create the search experience from the ground up. If you’re working from a newly created site, it’s a necessity. These steps show you how to switch to a manually configured search experience in the default site, but you can skip the step on deleting the default search page if you’re starting with a new site:

  1. Delete the existent search page by navigating to the default site’s menu and clicking BuildSite Pages. Click the Search page’s Options menu icon (icon-kebab-blue-on-white.png) and select Delete. Confirm you want to delete the page, and it’s gone.

    Once deleted, the search bar disappears from your site pages, replaced by a warning message visible only to site administrators:

    search-bar-warning.png

    Figure 4: The search bar is only visible if it points to an existent page.

  2. Create a new page named whatever you want (Finders Keepers, perhaps). Make it hidden or add it to the navigation as you please (the default search page is hidden from the navigation).

    If you want a pre-configured search page, create it from the Search page template. Find the template in the Add Site Page form. It’s under Global Templates.

    search-page-template.png

    Figure 5: There’s a handy page template for creating search pages.

  3. If you’re creating a page not backed by the template, add and configure all the widgets you need. You’ll find all the available search widgets in the Add Widget menu’s Search section. Lay them out however you want on the page.

  4. Configure the search bar at the top of the page, making sure it points to your new search page’s friendly URL (for example, /finders-keepers).

    Click the Search Bar widget’s Options menu (icon-kebab-blue-on-blue.png).

    Click Configuration and set the Destination Page to the search page’s friendly URL.

    Click Save.

Now your search page is up and running.

Legacy Search Experience

In prior versions, the search experience was encapsulated in one application, Search. It was embedded in the default theme, just like the search bar is now. It looked very similar, with only the search bar visible in the default view of the application. Once a search term is entered, the maximized view of the application is presented, with all the search facets and results now in view. It looks a lot like the new search behavior, only its monolithic structure means it’s difficult to customize. If you liked the old application, it’s still available. Enable it with these steps:

  1. Delete the default search page. From the site menu, click BuildPages. Click the Options menu (icon-kebab-blue-on-white.png) for the Search page and choose Delete.

  2. Enable the legacy search application. Go to Control Panel → Configuration → System Settings → Search → Search Web and check the box for Classic Search Widget in Front Page.

Now your portal’s search is backed by the legacy Search application, and it’s embedded on each page in the default theme. To add the legacy Search application to a page, open the Add Widget menu, find the Search widget under the Tools category, and drag and drop it onto the page.

Configure the portal’s search behavior to suit your needs. Here you’ve seen three distinct search configurations.

0 (0 הצבעות)
What’s New with Search? קודם